Objective

Note: Guidance on Palo Alto Networks firewalls is publicly available within Palo Alto Networks device documentation.

Applies To

• Palo Alto Networks Firewalls

Procedure

The purpose of this article is to provide a sample configuration. At the time of article creation, this device was in a known working state on the firmware used.  Keep in mind different firmware versions will interact with hosted VoIP services in different ways. While this device may be fully functional on the tested and/or current firmware version, it is possible newer revisions will cause disruptions in service or make a device fully compliant with the required settings for hosted VoIP services where it was previously not.

For Palo Alto Firewalls on firmware 8.0 and above.

Administrative Information

1. Make sure your firewall is powered on and connected to your network.
2. Connect the RJ-45 Ethernet cable from the RJ-45 port on your computer to the MGT port on the firewall.
3. If necessary, change the IP address on your computer to an address in the 192.168.1.0/24 range (e.g., 192.168.1.3).
4. In a browser on a computer on the same network as the Palo Alto Networks firewall, navigate to https://192.168.1.1
5. Log in (default credentials shown below).
   • Username: admin
   • Password: admin

Note: If you are not able to connect to the web interface, consult the quick start guide for your particular device model for additional options.

Configuring 8x8 Voice Services on Palo Alto Networks Firewalls

Add 8x8 Public IP Subnets

1. Go to Objects > Addresses.
2. Click Add.
3. Tags can be added only if they've been manually created under the Tags field, if not then leave it blank.
   
   
4. For a complete list of 8x8 subnets, see X Series Technical Requirements. 

Create an Address Group for 8x8 Public IP Subnets

1. Go to Objects > Address Groups.
2. Add all entries you created in the previous screen. (The Name can be whatever you prefer.)
   
   

Create a Security Rule on PAN System

1. Go to Policies > Security.
2. Click Add.
   
   
3. On the General tab, name the Security Rule and add a Description as desired.
4. On the Source tab, set Source Address or Source Zone (this is any subnet or zone that will have 8x8 phones or 8x8 8x8 Work Desktop or Mobile running on it).
   
5. Leave the User tab blank.
6. On the Destination tab, set the Destination Address by adding the Destination Address group you created earlier
7. Untrust (WAN/Internet) the zone for your network.
   
   
8. On the Application tab, click + add and add the following applications:
   • 8x8 
   • web-browsing
   • vidyo
   • stun
   • ssl
   • sip-application
   • sip
   • rtp
   • rtp-base
   • rtmpt
   • rtmp
   • rtcp
   • jabber
9. Set the Service/URL Category to ANY
   
   
10. On the Actions tab, set Action Setting to Allow.
11. Click OK.
12. Move the newly created security rule to the top of rule list to avoid rule conflicts.

Create an Application Override Rule for UDP

1. Go to Policies > Application Override.
2. Click Add.
   
   
3. On the General tab, name the rule and add a description.(Example below)
   
   
4. On the Source tab, set Source Address or Source Zone (this is any subnet or zone that will have 8x8 phones or 8x8 8x8 Work Desktop or Mobile running on it).
   
   
5. On the Destination tab, set the Destination Address by adding the Destination Address group you created earlier.
6. Untrust the zone for your network.
   
   
7. On the Protocol/Application tab, select UDP.
    
   
8. Add the following UDP ports into the Port field as indicated in picture below: 
   • 16150
   • 26384
   • 28591-28597
   • 28693
   • 5060
   • 5061
   • 5196-5199
   • 5299
   • 5399
   • 5301
   • 5401
   • 5443

1. For Application, select 8x8 App.
    
   
2. Click OK.
3. Commit Changes

Additional Information 

Known Issues  Specifically Fax services don't work reliably with the higher resolution codecs.

Additional Configuration

1. Download the 8x8_Palo_Alto_Networks_XML file to your computer and extract the file.
2. Go to Objects > Applications.
3. Click Import.
   
   
4. Import the downloaded XML file.